Sign in
Explore Guest Blogging Opportunities in Mineral Metallurgy
Explore Guest Blogging Opportunities in Mineral Metallurgy
Your Position: Home - Rubber Products - Fitting and Crimping Checks for EN853 2SN and EN857 2SC Hoses
Guest Posts

Fitting and Crimping Checks for EN853 2SN and EN857 2SC Hoses

Nov. 18, 2026

Fitting and Crimping Checks for EN853 2SN and EN857 2SC Hoses

Reliable EN853 2SN and EN857 2SC hose assemblies depend on matching the hose, fitting, and crimping method as one approved system. Before production, confirm the hose and fitting compatibility, follow the fitting manufacturer’s crimp specification, and verify the finished crimp diameter with a suitable measuring tool. Do not use a generic crimp setting: the correct value depends on the hose size, fitting design, and crimping equipment. These checks help reduce assembly errors, but they do not replace the manufacturer’s instructions or required assembly testing.

If you want to learn more, please visit our website.

Key checks at a glance

  • Confirm the hose marking, size, and fitting system before cutting or crimping.
  • Cut the hose square; check that the cut face is at 90° to the hose axis.
  • Use the specified insertion depth, die, crimper setting, and target crimp diameter for the exact hose-and-fitting combination.
  • Measure and record the crimp outside diameter in millimetres (mm), at the locations specified by the fitting instructions.
  • Inspect the completed assembly around the full 360° circumference for visible defects and fitting alignment.

Understand the hose before selecting a fitting

EN853 2SN and EN857 2SC construction

EN853 2SN and EN857 2SC are hydraulic hose designations associated with two-wire-braid reinforcement. Their construction and dimensions are not identical, so the designation alone is not enough to choose a fitting or crimp setting. Verify the hose size and the manufacturer’s technical information, then confirm that the fitting supplier lists that hose type as compatible. If the hose marking is unclear or the product has been cut from a larger coil, pause assembly until its identity can be confirmed.

EN857 2SC is commonly selected where a compact hose arrangement is useful, while EN853 2SN may suit other routing and equipment requirements. These broad distinctions do not establish interchangeability, equal pressure ratings, or a particular bend radius. Those values vary by size and product specification. Use the technical data for the specific hose supplied rather than applying a general rule across all sizes.

Step-by-step fitting and crimping checks

1. Confirm the assembly specification

Before production, document the hose type and size, fitting series and end connection, assembly length, orientation requirements, and crimping instructions. Check that the fitting manufacturer’s compatibility information covers the selected hose, rather than assuming that fittings for one two-wire-braid hose will suit another. Confirm the required crimper, die set, and target crimp diameter from the current instructions for that combination. If any of these details are unavailable, request clarification before making assemblies.

2. Inspect and cut the hose

Check the hose cover for cuts, crushing, exposed reinforcement, or other visible damage, and reject material that does not meet your acceptance criteria. Cut the hose with equipment appropriate to its construction, following the hose and tool instructions. A square cut helps the fitting seat evenly; inspect the face to confirm it is at 90° to the hose axis. Remove loose debris without allowing contamination to enter the hose bore.

3. Mark insertion depth and prepare the fitting

Establish insertion depth from the fitting maker’s instructions, then mark that depth on the hose so that it can be checked after assembly. Confirm whether the specified fitting system requires skiving or uses a non-skive method; do not remove the hose cover or reinforcement unless the instructions explicitly call for it. Check the fitting components for damage, contamination, or incorrect parts before installation. Keep the open hose and fitting clean throughout the process.

4. Crimp to the specified setting

Set up the crimper and dies according to their operating instructions, and use the crimp value specified for the exact hose-and-fitting combination. Position the fitting and hose correctly in the dies, and check any required fitting orientation before starting the cycle. Do not substitute a setting from a different hose size, fitting series, or machine merely because the parts appear similar. After crimping, confirm that the hose has not moved and that the insertion mark remains consistent with the fitting instructions.

Link to Hengshui Xinchi Hose Manufacturing Co., Ltd.

5. Measure and inspect the finished assembly

Measure the crimp outside diameter in mm with a suitable measuring instrument, using the locations and method specified by the fitting supplier. Compare the result with the applicable target and tolerance; do not invent a universal range for 2SN or 2SC assemblies. Inspect the crimp around the full 360° circumference for uneven forming, visible cracking, sharp damage, or other abnormalities. Also check fitting orientation, hose condition, and insertion depth before the assembly is released.

Check What to verify Acceptance basis
Hose identity Type, size, and condition Hose marking and product documentation
Cut face Square cut, checked at 90° to the hose axis Assembly procedure and visual inspection
Crimp diameter Measurement recorded in mm Fitting maker’s value and tolerance for the combination
Crimp appearance Full 360° visual inspection Fitting and quality-control instructions

Common mistakes to avoid

  • Mixing components by appearance: Similar-looking fittings may have different dimensions or crimp requirements. Verify the part number and compatibility information.
  • Using a remembered crimp setting: Settings can differ by hose size, fitting series, and crimper. Check the current instruction for every combination.
  • Skipping the insertion mark: Without a visible reference, incomplete insertion can be harder to identify. Mark the specified depth before crimping.
  • Assuming visual inspection proves performance: A neat-looking crimp does not establish pressure capability. Apply the inspection and test requirements defined for the assembly.
  • Ignoring cleanliness: Debris inside hydraulic hose assemblies can affect downstream equipment. Keep components protected during cutting and assembly.

Quality control and production records

For repeatable production, maintain a record of the hose and fitting identification, crimper and die selection, crimp measurement, inspection result, and operator or production batch reference where applicable. Define inspection frequency through your quality process and customer requirements rather than assuming that one sampling plan fits every order. If a measured diameter is outside the specified tolerance, quarantine the assembly and investigate the setup before continuing. Do not attempt an unapproved re-crimp or repair.

Pressure or proof testing should follow the applicable assembly specification and be performed with suitable equipment and safety controls by trained personnel. The correct test pressure and duration depend on the product and requirement; they should not be inferred from the hose designation alone. Keep people clear of pressurized assemblies and follow the test equipment manufacturer’s safety instructions. Record test results when the purchasing specification or quality plan requires them.

Buyer and supplier coordination

Buyers can reduce sourcing and assembly risk by sharing the hose type, size range, fitting details, working conditions, and expected order quantities when requesting a quotation. Ask suppliers to identify the applicable hose and fitting combination and to provide the relevant assembly instructions or crimp data where available. For custom assemblies, clarify length measurement points, fitting orientation, packaging, inspection records, and any testing requirements before order confirmation. These details help prevent avoidable differences between the requested assembly and the delivered product.

Hengshui Xinchi Hose Manufacturing Co., Ltd. supplies hydraulic hose products and can discuss hose selection and order requirements with B2B buyers. When requesting support for EN853 2SN or EN857 2SC hose, provide the required size, application, quantity, and any fitting or assembly specifications you already use. Our team can review the information available for the requested product and clarify which details need confirmation before production. Final fitting compatibility and crimp settings should always be verified against the selected fitting system’s instructions.

Conclusion: the checks that matter most

To check EN853 2SN and EN857 2SC hose fittings correctly, verify the hose identity, use a compatible fitting system, follow the exact crimp instructions, and inspect and measure the finished assembly. The practical checkpoints include a square 90° cut, a recorded crimp diameter in mm, and a visual check around 360° of the crimp. Because crimp values and acceptance limits vary by product combination, use the fitting manufacturer’s specification rather than a universal setting. For your next step, prepare the hose size, fitting details, and application requirements, then confirm the assembly procedure with your supplier before production.

Are you interested in learning more about Fitting and Crimping Checks for EN853 2SN and EN857 2SC Hoses? Contact us today to secure an expert consultation!

Comments

0 of 2000 characters used

All Comments (0)
Get in Touch

  |   Transportation   |   Toys & Hobbies   |   Tools   |   Timepieces, Jewelry, Eyewear   |   Textiles & Leather Products   |   Telecommunications   |   Sports & Entertainment   |   Shoes & Accessories   |   Service Equipment   |   Sitemap