6215-2RZ Deep Groove Ball Bearing: A Buyer’s Guide to Dimensions, Specifications, and Applications
The 6215-2RZ is a single-row deep groove ball bearing with standard boundary dimensions of 75 mm bore, 130 mm outside diameter, and 25 mm width. The “2RZ” designation commonly indicates non-contact seals on both sides, but seal naming and construction can vary by manufacturer, so confirm the exact configuration before ordering. For buyers, the key selection checks are shaft and housing fit, operating speed and load, lubrication, temperature, and the required sealing level. This guide explains how to evaluate those points and prepare a clear inquiry for Tuoda Bearing.
If you want to learn more, please visit our website.
Who This Guide Is For
This guide is intended for procurement teams, engineers, distributors, and maintenance buyers comparing 6215-2RZ bearings for new equipment or replacement. It is especially useful when a drawing or parts list identifies the bearing by number but does not provide enough information to confirm the correct variant. Buyers in automotive supply chains should verify the application requirements rather than assume that a standard bearing designation alone establishes suitability. The same checks apply to industrial equipment and general machinery.
Understanding the 6215-2RZ Bearing
Basic design and function
A deep groove ball bearing uses raceways in its inner and outer rings to support rolling balls. This design is commonly selected for radial loads and can also accommodate axial loads in both directions within the limits of its construction and operating conditions. The 6215 size designation identifies a particular bearing series and size; it does not, by itself, specify every detail of materials, internal clearance, precision, lubrication, or performance. Those details should be checked against the supplier’s product data and the equipment requirements.
What the 2RZ suffix means
In common bearing nomenclature, “2” indicates seals on both sides, while “RZ” is often used for a non-contact or low-contact seal design. Such seals can help retain grease and limit the entry of contaminants while avoiding the same type of rubbing contact found in some contact-seal designs. The actual seal profile, material, and performance are manufacturer-dependent, so do not rely on the suffix alone when sealing performance is critical. Ask the supplier to confirm the seal construction for the offered bearing.
Dimensions and Specifications to Confirm
The principal dimensions below are widely used for the standard 6215 bearing size. Treat them as a starting point for identification, then confirm the complete drawing and tolerance requirements for the specific product you plan to purchase. Other characteristics, including load ratings and limiting speed, can differ by design, cage, lubrication, seal arrangement, and manufacturer. Request the supplier’s current technical data rather than applying values from an unrelated 6215 variant.
| Specification | Common reference for 6215 | Buyer check |
|---|---|---|
| Bore diameter | 75 mm | Match the shaft diameter and fit requirement. |
| Outside diameter | 130 mm | Confirm the housing seat and available space. |
| Width | 25 mm | Check axial space and shoulder arrangement. |
| Seal arrangement | 2RZ commonly denotes seals on both sides | Confirm seal design and material with the manufacturer. |
Additional technical details
Before approving a quotation, specify any required internal clearance, cage type, precision class, lubricant, and operating temperature range. These properties may affect interchangeability and performance even when the boundary dimensions match. If the bearing operates at high speed, under vibration, or in a contaminated environment, provide those conditions to the supplier for review. Where a drawing or original part is available, sharing it can reduce ambiguity.
Tuoda Bearing Product Page
Materials and Configuration Options
Many standard deep groove ball bearings are produced with bearing-grade steel rings and balls, but buyers should confirm the material grade and heat-treatment requirements for the offered product. Stainless steel or other material options may be available for some bearing designs, though availability, load capacity, and suitability depend on the specific configuration. Seal materials and cage materials can also vary. If corrosion resistance, chemical exposure, or a particular lubricant is important, state it as a requirement rather than assuming it is included in a standard 6215-2RZ.
Applications and Application Matching
The 6215-2RZ may be considered for machinery that needs a 75 mm shaft seat and a bearing envelope of 130 mm by 25 mm, provided the load, speed, temperature, lubrication, and environmental conditions are compatible with the selected design. Deep groove ball bearings are used across many types of rotating equipment, including motors, pumps, and general machinery. Whether this exact sealed configuration is appropriate depends on the equipment maker’s specifications and the actual operating duty. In automotive-related equipment, verify the component drawing and service requirements before treating it as a direct replacement.
Match the bearing to operating conditions
Start by identifying the dominant load direction and the expected load level, then compare these with the supplier’s published ratings for the exact bearing variant. Record rotational speed and duty cycle, because a bearing’s permitted speed depends on its design, lubricant, and operating conditions. Consider whether the seals provide the required balance between contamination protection and friction. Finally, check shaft and housing fits, alignment, temperature, and installation method.
A Practical Buyer Selection Framework
- Confirm the part number. Verify that 6215-2RZ is the required designation and clarify whether the original specification calls for a particular manufacturer or equivalent.
- Match the dimensions. Check the 75 mm bore, 130 mm outside diameter, and 25 mm width against the shaft, housing, and available axial space.
- Define performance requirements. Provide load, speed, temperature, duty cycle, lubrication, and contamination conditions so the supplier can assess the configuration.
- Specify quality and traceability needs. State requested inspection documents, packaging, marking, and lot identification requirements. Confirm what the supplier can provide before placing an order.
- Review the quotation and sample requirements. Compare the offered specification with your drawing or application needs, and agree on any approval steps before production or shipment.
Pricing, MOQ, and Lead Time
The price of a 6215-2RZ depends on factors such as order quantity, specified materials and configuration, packaging, and delivery terms. Minimum order quantities and lead times are supplier- and order-dependent, so they should be requested for the exact specification and destination. A low unit price is not a complete comparison if the offered seal, clearance, documentation, or packaging differs from the required product. For a useful quotation, share the annual or initial quantity, target delivery schedule, and any inspection or labeling requirements.
Supplier Evaluation Checklist
- Can the supplier confirm the bearing’s dimensions and the exact 2RZ seal construction?
- Will the quotation identify the offered clearance, cage, lubricant, and material where specified?
- Can the supplier provide relevant product data and agree to the required inspection or traceability documents?
- Are MOQ, production or dispatch lead time, packaging, and delivery terms stated clearly?
- Is there a process for resolving specification questions before production and shipment?
Tuoda Bearing supports B2B buyers with bearing sourcing and specification review for the 6215-2RZ and related bearing requirements. To help us assess your inquiry, provide the required quantity, application, operating conditions, drawing or reference specification, and destination. We can then confirm the available configuration and quote details against the information supplied. Any requested customization or documentation should be agreed before order confirmation.
Key Takeaways and Next Steps
The standard 6215 bearing envelope is 75 mm × 130 mm × 25 mm, while the “2RZ” suffix commonly describes seals on both sides with a non-contact design. Exact seal construction and other performance characteristics should be verified with the manufacturer, especially when replacing an existing bearing or evaluating automotive-related equipment. Selection should consider fit, loads, speed, temperature, lubrication, contamination, and documentation—not dimensions alone. Send Tuoda Bearing your drawing or specification, operating conditions, quantity, and delivery requirements to request a configuration review and quotation.



