5 Steps To Choose The Right O-Ring

O-rings are robust sealing solutions for nearly endless applications in every industry. They will only work well, though, if you choose the right o-ring from the start. If you use the wrong material, profile, or size, your o-ring’s integrity will inevitably suffer and, ultimately, fail.

Dingtong Product Page

The good news is that you have the resources to make the right choice for your team right here. There are essentially five steps to choose the correct o-ring for your application. Barring unique application challenges, you should have the information to make the right decision for your seal after reading through these resources.

If you have any questions or unique considerations, our team is happy to help you find a solution quickly.

To determine if that step is necessary, let’s walk through the five steps to choosing the right o-ring for your application.

1. Identify Your Application’s Challenges

Before you can do anything else, you need to identify exactly what challenges your o-ring will face. We consider the following:

• Chemical exposure
• Ozone exposure
• Operating high temperatures
• Operating low temperatures
• High pressure
• Rapid decompression
• Static application
• Dynamic application
• Weather exposure
• Steam or hot amines

You should also be aware of any regulatory requirements of your application, such as USDA 3A, USP CL VI, or FDA CFR 21. 

Once you have the list of challenges your application will face and relevant regulations, you can get into the meat of choosing your o-ring.

2. Choose Your O-Ring’s Material(s)

One of the most important parts of choosing an o-ring is identifying the right material. A few popular options include FFKM, PTFE, EPDM, and NBR. 

FFKM

FFKM overcomes:

• Chemical exposure
• Ozone exposure
• Operating high temperatures
• Operating low temperatures
• High pressure
• Rapid decompression
• Static application
• Dynamic application
• Weather exposure
• Steam or hot amines

FFKM is best suited for high- or low-operating temperature applications and applications with aggressive solvents, chemicals, or media that would cause other materials to fail. It is used in almost every industry, particularly oil and gas, medical and pharmaceutical applications, and semiconductors.

PTFE

PTFE overcomes:

• Chemical exposure
• Ozone exposure
• Operating high temperatures
• Operating low temperatures
• Rapid decompression
• Static application
• Weather exposure
• Steam or hot amines

PTFE is best suited for applications that do not need a high compression set but also excellent chemical and temperature resistance. These include medical devices, coatings, and pest control. It also works well in ultra-low temperatures, like aerospace and automotive manufacturing.

EPDM

EPDM overcomes:

• Ozone exposure
• Operating high temperatures
• Operating low temperatures
• High pressure
• Rapid decompression
• Static application
• Dynamic application
• Weather exposure
• Steam or hot amines

EPDM is best suited for weatherproofing because it can withstand extreme elements. It is frequently found in roofing, windows, doors, cell towers, and other outdoor applications. It also works well with applications that use steam, automotive brake fluid, vibration dampeners, and isolators. 

NBR

NBR overcomes:

• Chemical exposure
• Operating low temperatures
• High pressure
• Rapid decompression
• Static application
• Dynamic application

NBR is universally used in basic sealing applications because it is low-cost and offers comprehensive benefits and physical properties. We see it often in automotive, water treatment and filtration, and pool and spa applications.

NBR can be formulated to excel in harsh environments, including aerospace and other low-temperature applications. 

Curious About Chemical Compatibility?

Use our comprehensive chemical compatibility guide to ensure the material that best meets your needs will also be compatible with the chemicals you use. The guide also includes a cost gauge to help you choose an option in your budget early on.

3. Choose Your O-Ring’s Profile

There are a few common profiles for an o-ring, but there are numerous solutions for a variety of challenges your seal might face. This knowledge is important, but we always have experts ready to help you choose the right material, profile, and size for your seal to ensure success.

With that being said, let’s lay out some profile basics!

O-Ring

First and foremost, there is the tried and true o-ring. O-rings are incredibly versatile and offer a wide range of solutions for almost any application and industry. These sealing solutions can also be paired with complementary fittings that help them function better in your application.

Pros

• O-rings are incredibly versatile. They are very customizable and come in various materials, colors, sizes, etc.
• They are one of the most common sealing solutions, making them readily available in a range of standard sizes, materials, and customization options.
• Because they are so widely available, o-rings are often cost-effective.
• If you are using o-rings in large quantities, you can purchase o-ring cord, which can be used to splice and vulcanize custom o-rings on-site.

Cons

• O-rings can sometimes be problematic in dynamic applications (twisting, rolling, etc.).
• They have limited high-pressure resistance. Thus, backup rings may be needed depending on your application pressure conditions.

While o-rings are often a solution, they might not be the best solution for your application.

X-Ring (or Quad-Rings®)

X-rings (or quad-rings®) are similar to o-rings, but their cross-section forms an X with four contact points. These are an alternative to o-rings and are recommended for low-speed reciprocating or oscillatory motions that are twisting, rolling, or bunching. 

Pros

• X-rings provide less friction than o-rings.
• They offer four points of contact when sealing.
• They are interchangeable with o-ring sizes and gland designs, making them an easy substitute. 
• These o-ring alternatives are available in the same standard sizes and custom sizes as o-rings, while being readily available in USA AS568 standard sized NBR Buna-N and FKM.

Cons

• X-rings are not recommended for pressures >500 psi.
• As they are more specialized, x-rings may not be available in all compounds.
• They are also a little more expensive than standard o-rings.

U-Cup Lip Seals

U-cup lip seals are in the same general shape as an o-ring, but the cross-section is a U. U-cups can function independently, but they also have the unique option of being “loaded.” A loaded u-cup has an o-ring or spring energizer nestled into its internal groove.

U-cups are designed for dynamic reciprocating applications up to PSI, but loaded u-cups can handle up to 5,000 PSI.

Pros

• U-cups have longer sealing life than o-rings because they experience lower levels of friction.
• These seals are also available in nonsymmetrical rod and piston configurations, which are common applications for u-cup seals.
• Polypaks® use an o-ring to provide sealing force at a low pressure.
• We can design custom lip seals for existing grooves that are not standard.

Cons

• Unfortunately, u-cups are more difficult to size than o- or x-rings.
• They are available in a limited array of materials and standard sizes.
• U-cup seals are a more expensive solution than other options.

Glyd Rings® 

Glyd Rings® combine the power of a Turcon-based slipper seal with an energizing o-ring to extend the life of an o-ring in dynamic, reciprocating applications. They use an interference fit that couples with the extra tightness of the o-ring to ensure a quality seal at lower pressure.

Pros

• Glyd Rings® are typically suitable for slow and fast reciprocating speeds running dry or lubricated.
• They can withstand pressures up to PSI in most applications.
• They operate at low friction with no stick-slip effect.
• Glyd Rings® are compatible with all o-ring materials.
• With a high wear resistance, they also offer minimal break-out force.

Cons

• Glyd Rings® cannot be stretched more than 5% during installation.
• They are not recommended for oscillating applications.

4. Size Your O-Ring

Sizing is by far the trickiest but most important part of choosing an o-ring. When we diagnose failed seals, an improperly sized o-ring is often the culprit.

To start, review gland design basics. Then, you will need to determine the way pressure works in your gland. Your operation will be one of the following:

1. Internal Pressure
2. Internal Vacuum
3. Dynamic Rod and Piston
4. Static Rod and Piston

Now, to determine your sizing, you will want to know the following gland measurements:

For Internal pressure:

• Inner Diameter
• Depth
• Width

For Internal Vacuum:

• Outer Diameter
• Depth
• Width

For Dynamic Rod and Piston:

• Outer Diameter Sealing Width
• D Diameter
• E Diameter
• F Diameter
• Inner Diameter Sealing Width
• II Diameter
• I Diameter
• G Diameter

For Static Rod and Piston:

• Outer Diameter Sealing Width
• D Diameter
• H Gap
• E Bore Diameter
• Inner Diameter Sealing Width
• H Gap
• G Tube Diameter
• F Gland Diameter

Now that you have your important measurements, you can use a comprehensive sizing chart to select the correct sized o-ring. The following links will take you to the corresponding sizing chart for your appropriate region:

USA O-Ring Sizing Chart

Common Metric O-Ring Sizing Chart

Japanese JIS O-Rings Sizing Chart

If you want to learn more, please visit our website oil seal custom.

Additional reading:
The Purpose of Hand Grips for Functional Training. - Element 26
3.2V 200Ah Rechargeable Prismatic LiFePO4 Cell with Custom ...
What is the Advantage and Disadvantage of Counterflow Fill

British BS O-Ring Sizing Chart

5. Choose Your Supplier

Last but certainly not least, you will need to choose your supplier. Your supplier should be your collaborative partner in consolidating and streamlining your sealing needs. To help you identify the exact questions you should be asking suppliers, we’ve included a comprehensive list in our Complete Guide To Choosing An O-Ring.

Get your free copy today!

Related Pages

Choosing the right oil seal kit for your motorcycle is crucial for maintaining its performance and longevity. Oil seals, also known as shaft seals or radial lip seals, play a vital role in keeping the engine oil from leaking and ensuring that contaminants do not enter the engine. Here's a comprehensive guide to help you choose the right oil seal kit for your motorcycle.

Understanding Oil Seals

Oil seals are designed to protect various parts of your motorcycle by sealing gaps between stationary and moving components. They prevent oil leakage, maintain lubrication, and keep out dust, dirt, and other contaminants. Common applications of oil seals in motorcycles include the engine, gearbox, and forks.

Steps to Choose the Right Oil Seal Kit

Identify Your Motorcycle Model and Year

The first step in selecting the correct oil seal kit is to know the exact make, model, and year of your motorcycle. Oil seals are designed to fit specific models, so having this information will ensure you get the right fit.

Oil Seal Kit 

Understand the Types of Oil Seals Needed

Different parts of your motorcycle will require different types of oil seals. Common seals include:

Fork Seals: Prevent oil from leaking out of the forks.

Engine Seals: Prevent oil from leaking out of the engine and keep contaminants out.

Gearbox Seals: Ensure smooth operation of the gearbox by preventing oil leakage.

Check your motorcycle's service manual to identify all the seals you need.

Choose the Right Material

Oil seals are made from various materials, each suited to different conditions and applications:

Nitrile Rubber (NBR): Commonly used for general-purpose seals. Suitable for temperatures up to 120°C.

Fluorocarbon (Viton): Ideal for high-temperature applications and exposure to harsh chemicals. Suitable for temperatures up to 200°C.

Silicone: Good for high-temperature applications but not suitable for high-pressure environments.

Polyacrylate: Used in high-pressure and high-temperature environments. Suitable for automotive applications.

Choose a material that matches the operating conditions of your motorcycle.

Check the Dimensions

Accurate measurements are critical for a proper fit. The three main dimensions to consider are:

Inner Diameter (ID): The diameter of the seal's inner opening, which fits around the shaft.

Outer Diameter (OD): The diameter of the seal's outer edge, which fits into the housing.

Width: The thickness of the seal.

Use a caliper or refer to the specifications in your motorcycle’s service manual to get these measurements.

Oil Seal Kit for Your Motorcycle

Consider the Seal Design

Different seal designs offer varying levels of performance:

Single Lip Seals: Suitable for general applications with moderate contamination levels.

Double Lip Seals: Provide additional protection by having an extra lip to keep out dirt and contaminants.

Spring-loaded Seals: Include a spring to maintain constant pressure on the sealing lip, ensuring better performance in dynamic applications.

Quality and Brand

Opt for oil seal kits from reputable brands known for their quality and reliability. Brands like SKF, NOK, and OEM parts are generally recommended.

Check reviews and ratings to ensure the kit you choose is durable and performs well under various conditions.

Purchase from a Reliable Supplier

Buy from authorized dealers or trusted online stores to ensure you get genuine and high-quality products. Avoid low-cost alternatives that may compromise performance and longevity.

Installation Tips

Preparation: Clean the area around the seal thoroughly before installation to prevent contamination.

Lubrication: Lightly coat the seal with oil or grease to ease installation and prevent damage.

Proper Tools: Use the correct tools to install the seals without causing deformation.

Check Alignment: Ensure the seal is properly aligned and seated to prevent leaks.

Conclusion

Choosing the right oil seal kit for your motorcycle involves understanding your specific needs, selecting the appropriate materials and designs, and ensuring accurate measurements. By following these steps, you can maintain your motorcycle's performance and extend its lifespan. Always prioritize quality and compatibility to keep your ride smooth and leak-free.

For more information on types of oil seals, please get in touch with King Seal.

Are you interested in learning more about polyurethane sealing ring? Contact us today to secure an expert consultation!